Webcome to Zhejiang Jovyea Plastic Co.Ltd.

+86-18257261120 sales@bestpvcfence.com

how to build a fence gate

Building a fence will facilitate increase home security and keep unwanted critters from your property. well-liked kinds of fences embrace privacy, picket, rail and basket-weave, and might be made up of such materials as wood, vinyl and metal.
Learning a way to build a fence involves securing the posts, attaching the panels or pickets and providing post caps. once putting in a fence, rigorously arrange the kind of fence you would like that matches your home and neighborhood.
1.Plan Your Fence
place restrictions on height and different factors. yard fences may be restricted to six to eight feet.
Fences typically will have longer lives supported their building materials. Treated cedar, one among the foremost sturdy, lasts up to forty years once properly put in and maintained.
Determine your border (your utility company will help) and the way you wish your fence positioned in relevance it.
As a courtesy, review any fence plans with neighbors United Nations agency share your border to go off any future disputes.
Select your fence kind initial therefore you’ll verify the offered widths of every fence panel.
Determine wherever you wish to find your gates and paint parallel lines to point the gate placement. live and document all gate sizes.
Subtract the gate footage from the fence footage to work the linear footage of the fence, then divide the linear footage of fencing by the panel length of the design fence you chose. this can verify the entire fence panels or pickets you would like. Remaining footage would require a partial panel. To calculate breadth once exploitation pickets, verify each your picket breadth and spacing between pickets.
For every panel and partial panel, add 2 to derive the entire fence posts required, and, if you’re adding post caps, the amount of post caps required and any trim needed.


2.Measure and Lay Out the Fence Posts
Outline your projected delimitation with paint, then live the define of your fence perimeter with a measure wheel.
Use chalk lines as a guide.
Position the fence posts each vi to eight feet on the road wherever you wish the fence to square. confirm the areas between the posts square measure consistent.
3.Dig Holes
With a post hole digger, dig holes close to thirty three p.c as deep as they’re tall (an 8-foot post desires a hole a minimum of two 1/2 feet deep), and many inches for gravel. Avoid utility lines and pipes. In colder climates, dig below the frost line.
4.Add Concrete and Gravel and Position Posts
Once the holes square measure mamma, pour three to four inches of gravel down the bottom of the opening for correct drain.
Add vi to eight inches of concrete combine once the gravel is about.
Position the post within the middle of the concrete combine, ensuring to slope the concrete combine faraway from the post.
Plumb post with A level.
Follow the manufacturer’s directions to permit for correct drying and solidifying time, which can take up to 3 days.
5.Attach Rails or Panels to Posts
Once the concrete has cured, attach the wood fence rails or wood fence panels to the posts.
Secure every rail with No. eight two 1/2-inch deck screws or galvanized 10d x 3-inch nails. Power drills or claw hammers square measure effective tools for this step.
Panels square measure usually quicker to construct. If you’re exploitation panels, proceed to Step seven once the panels square measure secured to the posts.
If you employ vinyl, chain link or Al for your fence, use deck screws rather than nails.
6.Attach Pickets to Rails
Once the rails square measure in situ, begin attaching the pickets to the rails.
Secure every picket with No. eight two 1/2-inch deck screws or galvanized 10d x 3-inch nails. Screwdriver sets may be useful during this method.

7.Attach Post Caps
To finish building a fence, attach the post caps to the posts.
Tap every cap gently with a rubber mallet till all fits snugly onto the post.
8.Stain or Treat the Wood
After building a fence, staining or treating the wood may be the primary step in correct maintenance which will extend its life.
When the fence is in situ, apply paint, stain or a weather-proofing end in line with manufacturer’s directions.
Apply wood preservative round the base posts to stop the wood from decomposition.
If the fence is constructed of pressure-treated wood, wait till the wood has totally dried before applying stain or end. Pressure-treated wood mustn’t want further protective or water-proofing.
Apply new coats each two to three years, and make certain to scrub the fence with a wood or fence cleaner the day before application.

PREV
NEXT

RELATED POSTS

Inquiry

Skype

WhatsApp

WangWang

QQ
Email me

Mail to us