Webcome to Zhejiang Jovyea Plastic Co.Ltd.

+86-18257261120 sales@bestpvcfence.com

How to Install a Picket Fence

Upload fashion across the perimeter of your backyard with this classic-fashion fence.

Introduction

Select the site and Plan the layout

Watch video of this step.

When identifying the proper fence to your venture, don’t forget the function of the fence. some fences are constructed simply to enhance the landscape or create a gentle boundary. Others are built for privacy or security. however whilst cut down appeal is the point of interest, a picket fence is a conventional charmer. usually hooked up along the road-dealing with fringe of a backyard, its extraordinary, acquainted shape is an appealing preference.

For our undertaking we’re building a 4-foot tall wood fence. The equal kind of construction can be used to construct a privateness of protection fence, simplest the forums would be taller and geared up closer collectively.

Accurate fencing etiquette calls for the finished side of the pickets to be going through outward. The framing is on the internal of the fence facing your private home.

Earlier than digging, continually consult your nearby application and cable corporations and have them mark the vicinity of any underground offerings.

If you are nevertheless honing your woodworking abilties, you might want to take into account the usage of prefabricated fencing sections.

STEP 1

To start the fence, degree the location where you’d like to build it. area stakes in the ground at approximately a foot or two beyond where you want the give up posts

Use a post-hollow digger to make a hollow eight inches wide and just over 2-toes deep. Your holes on your your fence posts must be 6 to eight feet apart.

Pour about four inches of gravel for the bottom, and then insert the eight-foot 4×4 publish into the hollow. Then pour dry concrete into the hollow surrounding the submit. Use a 3-manner degree to ensure the put up is status directly. Tamp down the dry concrete.

Degree and Set the primary post

Watch video of this step.

To begin the fence, measure the place where you’d like to construct it. Our fence could be 48 toes long. area stakes within the floor at about a foot or beyond where you need the end posts.

Join a taut string as a guide for the course of the fence. close to one give up of the manual string, make a mark for the first outdoor post. the primary submit is placed in which you want the fence to start.

Frequently, set fence posts approximately 6 to 8 feet apart. A fence that is 48-ft long could have six to 8 posts.

Use a submit-hole digger to make a hole eight inches extensive and simply over 2-toes deep.

Pour approximately four inches of gravel for the bottom, and then insert the 8-foot 4×4 submit into the hole. Then pour dry concrete into the hollow surrounding the publish. Use a 3-manner stage to make sure the post is standing straight. Tamp down the dry concrete.

In slight climates, many contractors use this dry concrete approach, which attracts natural moisture from the floor to harden or “set” the packed concrete across the put up.

Another choice is speedy drying concrete mix. once positioned inside the holes, it will absorb to 48 to seventy two hours to dry.

STEP 2

Once the primary outside put up is ready, the alternative outside post is subsequent. observe a manual string, and measure 48 ft to the alternative stop, and mark it at that spot.

To set the second one outside post, follow a manual string, and measure 48 toes to the other cease, then, mark that spot.

Transfer the guide string from the stakes to the posts themselves to make certain that your outside posts are level.

Set the indoors posts the usage of the string to divide the forty eight-foot span into six equal sections 8 feet apart, marking each on middle with a piece of covering tape positioned on the string.

The use of a plumb bob, switch the marks from every piece of overlaying tape to the floor. using these marks and the string as a guide, dig holes and set the indoors fence posts, making sure every one is degree and plumb with the others

Set the closing Posts

Once the first outdoor put up is set, the alternative outside put up is next. comply with a manual string, and degree forty eight feet to the other end, and mark it at that spot. Dig a hole and set the second outside post, making sure the out of doors face of the publish is parallel to the sidewall and the primary publish.

Subsequent, transfer the guide string from the stakes to the posts themselves. Then set the indoors posts the use of the string to divide the forty eight-foot span into six identical sections eight ft aside, marking each on center with a chunk of covering tape placed at the string.

The usage of a plumb bob, switch the marks from each piece of covering tape to the floor. using those marks and the string as a guide, dig holes and set the interior fence posts, ensuring every one is level and plumb with the others.

At this point within the manner, the posts are taller than required. Trim to proper top once the rails and pickets are attached.

STEP 3

From the bottom of every post, degree up 12 inches for the lower rail and 36 inches for the top rail. Make a mark at ninety levels on the lower back of the posts.

Attach the rails to the posts using three-inch galvanized metallic force screws.

After rails are connected to the posts, reduce off the excess in order that the rail is flush with the put up.

Installation the Rails

Watch video of this step.

With the posts set, cut 2x4s into twelve 8-foot lengths for horizontal fence rails to be able to support the pickets.

From the base of every put up, measure up 12 inches for the lower rail and 36 inches for the pinnacle rail. Make a mark at 90 tiers at the returned of the posts.

Attach the rails the use of two three-inch galvanized metal force screws. remember the fact that the marks ought to serve as the pinnacle edge of the rails, with each rail butting in opposition to the next one on the returned of each submit.

Rails connected to outer posts are cut to connect flush with the edge of the submit.

STEP 4

Lay out the pickets with 2 to 3 inches in between. Use a three inch huge degree to set your areas.

Lay a leveled 2×4 on the floor beneath the rail to apply as a base for keeping a steady top of two inches from the ground. calmly spacing the pickets as you pass, attach them to the rail the use of a nail gun
install the Pickets

Watch video of this step.

If you’re nonetheless honing your woodworking skills, you would possibly need to recollect the usage of prefabricated fencing sections.

Lay out the pickets with 2 to three inches in among, we decided to apply a 3-inch-huge stage as our spacer. you can create your own spacer jig with a bit of wooden, plastic or drywall.

Lay a leveled 2×4 on the floor beneath the rail to apply as a base for retaining a regular peak of 2 inches from the floor. evenly spacing the pickets as you pass, attach them to the rail using a nail gun.

STEP 5

The very last step is to cap the fence posts with finials. On every submit, degree one inch up from the pickets and keep the mark across the publish using a square.

After putting off the top of the put up the use of a round or reciprocating noticed, connect the ornamental finial with finishing nails.

Finishing Touches

Watch video of this step.

The final step is to cap the fence posts with finials. On each put up, degree one inch up from the pickets and hold the mark around the submit using a square.

Cast off the pinnacle of the publish the usage of a circular or reciprocating noticed. attach the ornamental finial with finishing nails.

PREV
NEXT

RELATED POSTS

Inquiry

Skype

WhatsApp

WangWang

QQ
Email me

Mail to us